Few of us girls do not dream of shining in the host of Hollywood stars. We largely imitate famous actresses, doing makeup like them, putting on similar in style things, doing similar hairstyles. Accessories - also an important detail of the image, and the famous bracelet "Hollywood" just drives everyone crazy. But with a great desire, you can weave it out of rubber bands and become a little closer to your dream of being like a star.
How to weave bracelets from rubber bands "Hollywood"?
The process of making such an accessory is rather difficult and time-consuming. Weave a bracelet "Hollywood" from rubber bands only on a special machine. In addition to it we will need a hook and a lot of rubber bands of different colors. In this master class three colors are used: red, yellow and pink.
So, let's proceed to a step-by-step description of the process of weaving the bracelet "Hollywood" out of rubber bands:
- Part of the machine is removed from the substrate. We need only two rows, and they need to be arranged so that the open sides of the columns look to the right. We need the last 8 columns. First we just put on them 2 red gum as follows:
- Now we take a hook in our hand and do the following: throw the rubber on each of the posts so that the crosshairs from their inner sides are obtained. As a result, we should get 8 posts with cross-hairs made of rubber bands. After - a little lowering the gum down.
- Again, take 2 gums of red color and throw on the posts, as in the very beginning. And once again we repeat this action, that is, on each of the two groups of columns, we should have 3 red gums each. Between the two inner lower bars we stretch the elastic band of yellow color.
- Again, we take the hook in hand, the lowest red rubber band with its help on each column is pulled up and gradually weighed on them, as if throwing inside the pillars. Do not touch only those two bars on which the yellow rubber band is stretched - with them we'll work a little differently.
- On the middle posts with a yellow rubber band, we act like this: we hook the hook inside the rubber band, grab the bottom left red rubber band and put it on the post. To remove the elastic from the right column, you need to pull the back of the hook inside the yellow elastic band, while grabbing the lower red gum and throwing it on the post.
- After that, we lower the whole structure down a bit and again put 2 red bands on two groups of posts, and over the yellow elastic band we pull the pink band.
- Again we throw off the bottom red rubbers, leaving the central ones. With them, we remove the rubber bands in the same way as described above - starting the hook between now two central elastic bands for the left column, pulling them and clinging the bottom red for the folding to the right column.
- Again, pull 2 red gum on 8 bars, in the middle - yellow or pink (alternate them) and repeat all the manipulations, until we reach the moment when we have 4 gum (2 yellow and 2 pink) on the middle posts. From this moment we begin after all the drops of the red rubber bands with each new layer, the lowest middle elastic is discarded for two bars (inside).
- Continue all the manipulations until the moment we get the right length of the bracelet. Please note that it will come out from below, so there should not be a base under the posts.
- When the desired length of the bracelet is already there, you need to remove it from the machine. For this purpose we throw 2 red elastic bands on columns as usual, and on the center of anything to throw it is not necessary any more. Again we remove from each column the bottom red elastic, in the center we throw off the pink elastic band, despite the fact that there are only 3 of them now.
- Again, pull 2 red gums on the right and left, on the central bars again do not throw. As usual, we take off the lower elastic band from each table, and from the central two columns - yellow. We put another layer of red gum. Now, when in the center we have one pink rubber band, we throw off not one lower red, but two elastic bands from the columns at once. The last central rubber is also dropped inside.
- Now we make 2 out of 8 bars: we drop all the bands on the central columns.
- It remains to attach the hooks to the bracelet and connect the two ends with their help:
With the help of our master class you learned how to make a bracelet "Hollywood" made of rubber bands, and now a similar accessory can also become a part of your image.
