Finishing loggia lining - all the subtleties of the technology of plating and insulation

The most popular is the finish of the loggia lining, which has its advantages and disadvantages. There are several finishes and a lot of ideas in the design. Finishing works are not considered difficult, therefore, knowing the instruction, they can be handled independently.

Lining on the loggia

When choosing the right material for finishing, it is recommended to familiarize yourself with the existing advantages and disadvantages. Let's start with the advantages of finishing the balcony with a lining:

• prevents the development of mold;
• high reliability and durability;
• ecological compatibility;
• increases thermal insulation;
• simplicity of installation.

The interior finish of the loggia has also disadvantages:

• it is necessary to use antiseptics;
• fire dangerous;
• the surface of the walls must be prepared;
• relatively high price.

Options for finishing the balcony with lining

Before carrying out repairs, it is necessary to determine what the lining will be used for. Finishing the loggia inside the lining can be of this type:

1. Cold. This option is suitable if there is no insulation. In this case, the material is simply attached to the wall, but it should be taken into account that the temperature on the loggia and on the street will be the same.
2. Warm. The most common version of the finish, which implies pre-insulation. If you want, you can heat the loggia.
3. Reorganization. This option is suitable for situations where the loggia and the room are merged. To conduct such work without fail is necessary with warming.

Design of the balcony by the lining

Do not think that with the use of lining the finish will be ugly, because there are a lot of design options. The lining of the loggia can be complete with a wooden lining, that is, the material is fastened to walls, floor and ceiling. You can use wooden panels only for walls. Lining in this regard is almost universal and it is well combined with plaster , wallpaper, natural and decorative stone and so on.

How correctly to sew a loggia with a lining?

During the repair work, it is recommended to start with the creation of a triple barrier. First put plaster PVA, then the insulation and sealing is carried out, and after that the crate, on which the MDF boards are fixed, is stuffed. After that, you can go to the main works, for which the instruction is useful, how to sew the loggia with the lining:

1. First you need to trim under the size of the board. Put the first bar into the corner with a comb from the corner. Attach it with 3-4 small nails to the logs or MDF. Repeat the manipulation of all the boards.
2. Cut the last board in width in size, taking 1-2 mm. On the penultimate bar, it is necessary to cut the tongue half and round it.
3. The last two boards should be put in the groove "house" immediately, and then press the palms on top and bottom to the click.
4. The corners should be closed with slats or plinth. On this work can be considered complete.

There are a couple of tips that are given by experienced builders, so you can get a more perfect result. First, the nails for fastening the boards must be clogged closer to the root of the ridge with a slight inclination inward. Secondly, after adjusting the boards there are trimming, on which it is recommended to train to put the last two boards.

How to insulate the balcony with a lining?

Many for finishing this room choose a lining, because for its fastening a crate is created, into which it is possible to lay a heater.

1. Glass wool. The lining of the balcony with lining allows the use of this material, but it is only important to remember that during operation it is necessary to use protective means. In addition, the coefficient of thermal conductivity is inferior to modern types of insulation.
2. Mineral wool . Can be pressed and roll. It is necessary to provide additional steam and water protection. Mineral wool is afraid of moisture and is expensive.
3. Polyurethane foam. This is a sprayed insulation, which has high heat-saving properties. This option ensures tightness and does not shrink. Warming can only be carried out by specialized companies.
4. Styrofoam. Finishing loggia lining can be carried out and with the help of a heater that is not afraid of moisture and shrinkage. Very popular option.

The better to cover the lining on the loggia?

There are several options suitable for processing interior finishes, with their own characteristics. If you are interested in what to process the lining on the loggia, then choose among such tools:

1. Lucky. On the glazed balconies you can use water-based varnishes that are environmentally friendly, durable and safe. Alkyd varnishes form a water-repellent film on the surface, but they dry for a long time and unpleasantly smell. In addition, you can use acrylic and polyurethane varnishes.
2. Paints. This option is used in cases where cover defects should be hidden. For the balcony, oil, facade and thick alkyd paints are suitable.
3. Impregnation. These funds penetrate deeply into the structure of the tree and perfectly protect the material. Use can be stain or impregnation based on wax.